Three sand filter-manufacture,factory,supplier from China

1. Check the condition of the pressure gauge to see if it is working properly.2. Check the pressure values of pressure gauge 1 and pressure gauge 2, when the difference between the pressure values of the two pressure gauges exceeds 0.02GP, clean the filter screen.

When the filter is working normally, the pressurized water flows into the tank from the water inlet and reaches the filter layer evenly. When the water flows through the filter layer, the impurities are filtered and retained. There is a water trap with a valve at the bottom of the filter, and the filtered water is collected evenly and then flows out of the filtering equipment.With the continuous accumulation of impurities in the filter layer, the water flow loss continues to increase.

Components used in drip irrigation (listed in order from water source) include: Pump or pressurized water source. Water filter(s) or filtration systems: sand separator, Fertigation systems (Venturi injector) and chemigation equipment (optional) Backwash controller (Backflow prevention device)

Precise filtration: Filter discs with exceptional precisions may be selected in step with the water requirements. There are 20 microns, 55 microns, one hundred microns, 130 microns, two hundred microns, 400 microns and other specifications, and the filtration ratio is extra than 85%.Thorough and efficient backwashing: Because the filter pores are completely opened during backwashing, and the centrifugal jet effect is added, the cleaning effect that other filters cannot achieve can be achieved.

The stack clean out is composed of a hard and fast of plates with grooves on each sides. the intersection point shaped with the resource of the rims of the grooves can intercept the solids in the water.

The pipe joint with three openings is called tee pipe. Tee pipe is widely used in the pipe network conveying liquid and gas. Due to different conveying media, the material of tee pipe is divided into: cast copper, cast aluminum, plastic, cast iron, cast steel, glass, etc. tee is also widely used.Introduction:As the name suggests, there are three openings, i.e. one in and two out, or two in and one out. It is a kind of chemical pipe fittings, T-shaped and Y-shaped. It has equal diameter nozzle and reducing nozzle. It is used for the collection of three identical or different pipelines.

Fertilization flow of three-channel fertilizer applicator:1. First of all, the dissolved fertilizer solution into the fertilizer pot, open the main pump, through the regulating valve will be filled with water, closed water injection valve (the process of irrigation valve can always open) . When fertilizing, the “Time knob”in the control cabinet is used to adjust the time of fertilizing, the pump starts, the fertilizer in the tank is pumped into the main pipeline water by the pump, and the fertilizing is finished at the same time.

Setting up a drip irrigation system can be daunting — there are so many products to choose from, and often hardware stores carry whacky supplies. First and foremost, don’t buy a soaker hose! A soaker hose is notorious for uneven watering, it breaks down quickly, and is a hassle to repair. There are far superior products that are cheaper, last longer, and are simple to repair. In short, there are three different drip products to use, depending on your application:• Half-inch emitter tubing.

1. The location of the water source and the head hub is generally selected in the middle of the plot, and the location is higher.2. When irrigating, the position of the water inlet is high, and ensure that the position of the drain well is at a lower position.3. Generally, the water delivery and distribution pipelines of the drip irrigation system can be divided into three-stage pipelines: main pipe, branch pipe, and capillary (drip irrigation tape (pipe)), and some systems are equipped with branch pipes. The pipelines at all levels are arranged vertically with their superior pipelines.4.

This product is used when the drip irrigation system uses tape as the main pipeline. The branch water source, the main pipeline (soft belt) is connected with the drip irrigation belt, so that the water in the main pipeline (soft belt) flows into the drip irrigation belt separately.Use a punching machine (diameter 14mm) to make holes on the side of the soft water belt, then screw the tee into the hole of the soft water belt, tighten the nut to fix the bypass on the soft water belt, and connect the soft water belt to the other side of the drip irrigation belt.

1. AdvantagesSave water, fertilizer and laborDrip irrigation is a full pipeline water delivery and local micro-irrigation, which reduces the leakage and loss of water to the lowest limit. At the same time, because it can supply the water required by the crop root zone in a timely manner, there is no problem of peripheral water loss, and the water use efficiency is greatly improved. Irrigation can be conveniently combined with fertilization, that is, dissolve the chemical fertilizer and pour it into the irrigation system.

In recent years, there are a variety of popular orchard irrigation methods, such as immersion irrigation, manual irrigation, water-saving irrigation, high-level sprinkler irrigation, and simple sprinkler irrigation. However, these technologies all have their shortcomings more or less. The cost of immersion irrigation is high, and the cost of manual irrigation is high. The effect is relatively poor. Water-saving water-saving irrigation has low one-time investment, high water-saving efficiency, simple maintenance in the later stage, and high-level sprinkler irrigation.